门套现在是没有标准规格的，都是按照实际情况来定，不过正常门套厚度在12毫米以上为宜，若在12毫米以下，踢脚线会露出一个口来，因此厚度不足12毫米的门套线，需要加层。若较为高档的房屋装修或开发商未做统一规定的话，可以根据家里的门洞尺寸来定做的。

　　There is currently no standard specification for door frames, which are determined based on actual conditions. However, the normal thickness of door frames should be above 12 millimeters. If it is below 12 millimeters, the skirting board will expose a hole. Therefore, door frame lines with a thickness less than 12 millimeters need to be layered. If the high-end house decoration or developer does not have unified regulations, it can be customized according to the size of the door opening in the home.

　　门套怎么固定在墙上

　　How to fix the door frame on the wall

　　1、基本框架：选择结实的木头做芯材，按照原先良好的门套尺寸将木板裁成等宽大小，做成门框的基本框架。首先确定位置，用红外线水平仪在墙上标出水平线，然后测量出门洞的大小，两边用墨斗弹垂直线。

　　1. Basic framework: Choose sturdy wood as the core material, cut the wooden board into equal width sizes according to the original good door frame size, and make the basic framework of the door frame. Firstly, determine the position, mark the horizontal line on the wall with an infrared level, and then measure the size of the doorway. Use an ink fountain to draw straight lines on both sides.

　　2、墙上打眼：用充气钻在墙上打眼儿，加上木楔，这个时候记得做好标记。这个时候要将门套各个方向垂直水平安装，保证框架直角是否平直，然后将钉子穿过门框，钉入木楔子，将门框固定在墙上。

　　2. Wall drilling: Use an inflatable drill to drill holes on the wall, add wooden wedges, and remember to mark them at this time. At this point, the door frame should be installed vertically and horizontally in all directions to ensure that the right angle of the frame is straight. Then, nails should be inserted through the door frame and into the wooden wedges to fix the door frame to the wall.

　　3、一层叠级：将门套基本框架固定好以后，就可以做叠级了，这个目的是为了日后开关门关更加方便，距离大概在4-5CM左右。

　　3. One layer stacking: After fixing the basic frame of the door frame, the stacking can be done for the convenience of opening and closing the door in the future, with a distance of about 4-5CM.

　　4、贴面板：以上步骤安装完毕后，就开始贴面板了(先检查同一扇门的面板是否色差相近，边缘有无毛刺)，首先要测量好尺寸，接着裁剪面板，交界处缝隙严密。

　　4. Panel pasting: After the above steps are installed, it is time to start pasting the panels (first check whether the panels of the same door have similar color differences and whether there are burrs on the edges). First, measure the size, then cut the panels, and ensure that the gaps at the junction are tight.

　　5、安装木线条：当面板贴完之后，就可以开始安装木线条了。由里向外保留出1CM的距离，做上标记，然后将裁好的木线条根据标记进行安装，这样做会让整体的门套就更加美观了。这个时候一定要注意门框与地面之间大概留取5CM的空间，保证其他工序正常进行，如地面找平、贴地板或瓷砖的时候，可以有足够的空间。

　　5. Installation of wooden strips: After the panel is pasted, you can start installing the wooden strips. Leave a distance of 1cm from the inside out, mark it, and then install the cut wooden wire according to the mark. This will make the overall door frame more beautiful. At this time, it is important to leave a space of approximately 5CM between the door frame and the floor to ensure that other processes proceed normally, such as leveling the floor, tiling, or tiling, with sufficient space.

　　6、门挡线：用射钉枪把门挡线钉在门套线上，再固定好入门挡线和静音条。正好压住前后门框线的接缝处，钉子要注意，不要一次性全钉进去，因为有可能会导致门框歪斜，将多余的木塞锯掉。

　　6. Door stop line: Use a nail gun to nail the door stop line onto the door frame line, and then fix the door stop line and mute strip. Just press down on the seam of the front and rear door frame lines, be careful not to nail all at once, as it may cause the door frame to tilt and saw off excess wooden plugs.

　　7、表面清洁：等门套安装好以后，最后做好木门套的表面清洁工作。

　　7. Surface cleaning: After the door frame is installed, finally clean the surface of the wooden door frame.

　　本文由 滨州不锈钢电梯门套  友情奉献.更多有关的知识请点击  http://www.weixindf.cn/   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Binzhou Stainless Steel Elevator Door Frame For more related knowledge, please click http://www.weixindf.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Stay tuned