不锈钢电梯门套避坑指南，教你怎么选今天给大家分享一下不锈钢电梯门套的一些干货。

　　A guide to avoiding pitfalls with stainless steel elevator door frames, teaching you how to choose. Today, I will share with you some dry tips on stainless steel elevator door frames.

　　①颜色：现代简约风颜色选黑色喷砂哑光，黑色拉丝哑光细纹，深灰色喷砂哑光都可以，都是防指纹的，这几个颜色做的也最多，看着大气。②厚度：板材厚度的话从平整度上来说市场上0.8mm厚都完全可以了，安装上之后不会出现凹凸不平的情况。

　　① Color: Modern minimalist style color options include black sandblasted matte, black brushed matte with fine lines, and dark gray sandblasted matte, all of which are anti fingerprint. These colors are also the most commonly used and look atmospheric Thickness: In terms of flatness, a thickness of 0.8mm on the market is sufficient for sheet thickness, and there will be no unevenness after installation.

　　③材质：材质的话室内家装正常201都没问题，颜色可选性多一些。201的硬度也高面上不容易有坑，家装完全没问题（浴室卫生间除外）。304虽然防锈能力好一些，但是材质偏软，价格稍高，颜色可选性偏少，加工和运输途中稍不注意容易磕碰有坑。

　　③ Material: If the material is used, indoor decoration can be done normally without any problems, and there are more color options available. The hardness of 201 is also high, and it is not easy to have pits on the surface, so there is no problem with home decoration (except for bathrooms and toilets). Although 304 has better rust prevention ability, the material is relatively soft, the price is slightly higher, the color options are limited, and slight carelessness during processing and transportation can easily cause scratches and dents.

　　④加工工艺：然后就是加工工艺必须是刨槽工艺折弯，门套正面宽度在能盖住墙缝的前提下尽量窄#一些，但并不是越窄越好，尽量不低于10mm，建议15mm~20mm。这个可以根据洞口尺寸的大小相应的调整。侧面的话正常凸出墙面10mm，最好不低于这个尺寸，方便后期安装踢脚线收口。⑤安装：安装工艺的话就是找专业的不锈钢师傅，切45度对角安装，侧面阴角最好不要打胶。这个安装工艺很关键，有些木工师傅也能安装但是能装和装好就是另一回事了。安装好之后洞口宽的话用木龙骨或木方撑一下中间的位置，防止结构胶当时没干然后下垂。最后就是等到保洁的时候担保坨腊坦境都可以了专业的重要找专业的。

　　④ Processing technology: Then the processing technology must be groove cutting and bending. The front width of the door frame should be as narrow as possible while covering the wall gap, but it is not necessarily the narrower the better. It is recommended to be no less than 10mm, and it is suggested to be 15mm~20mm. This can be adjusted according to the size of the opening. On the side, it is normal to protrude 10mm from the wall, preferably not less than this size, to facilitate the later installation of the skirting board closure Installation: In terms of installation process, it is recommended to find a professional stainless steel technician and install it diagonally at a 45 degree angle. It is best not to apply glue to the side corners. This installation process is crucial, and some carpenters can also install it, but being able to install and install it is another matter. If the opening is wide after installation, use wooden keel or wooden square to support the middle position to prevent the structural adhesive from not drying out and sagging. Finally, when it comes to cleaning, it's important to find a professional to ensure that the Tuola Tanjing is ready.

　　本文由 淄博电梯门套 友情奉献.更多有关的知识请点击   http://www.weixindf.cn  真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Zibo Elevator Door Frame. For more related knowledge, please click http://www.weixindf.cn Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned